Mega Flux Cores used.
Capable of handling very high DC bias current with minimal inductance roll off.
Through hole mount with pre-tinned leads that can be directly soldered to PCB
Normally our customer specify the specs ( size, inductance, current)and we build to meet the specs.
Inductance range from: 13 uH to 600 uH
Current range to 8.0 Amps to 80.0 Amps
Also available in MPP, Sendust/KoolMu cores.
Series Mega Flux Toroidal Power Inductors.
Through Hole Mounting Construction
- Designed using
high saturation and high temperature stability "Mega Flux Cores"
with distributed air-gap
- Excellent electromagnetic
shielding due to toroidal design
- Designed for
commercial, industrial and military application
- Low cost designs
with pre-tinned leads for PCB through hole mounting
- Inductance values
from 13 uH to 600 uH
- Current rating
from 8 Amps to 80 Amps
- Temperature Rating:
-55 deg C to +125 Deg C
- Potted version
available for military application
- Custom designs
are available to meet your specific requirements
1) No tooling or set up fees required for standard parts
2) FREE Samples available for large OEMs
3) Typical Delivery: 4
to 6 weeks
) The prices
shown below are for low volume quantity. Please call 800-377-3244
email email@example.com for larger
volume OEM pricing.
2 ) Our large
OEM pricing is extremely competitive. We will meet or beat any competitors
prices with better deliveries
) Custom designs
are available to meet any of your requirements. Please contact us
) The data shown below can be sorted by clicking each column header.Click once again to sort in reverse order.
5) "Inductance at 1 Khz" ( 2nd column from left in table below ) is the inductance measured at zero or very low DC bias current.
6) "Current Rating" ( 3rd column from left in table below ) is based on a 40 deg C temperature rise at an ambient
temperature of 90 deg C. This is the DC bias current through the inductor that will cause the inductor will reach a max. temp. rise of 40 deg C. above ambient with NO AIR FLOW.
7) "Incremental Current for 20% inductance drop" ( 4th column from left in table below ) is the DC bias current
that will cause the inductance to drop by 20% from the value shown in Inductance at 1 Khz. At this current, the temperature rise may be above the 40 deg C stated above, so forced air flow may be required.
8) The saturation current is at least 5 times the max current listed in 5) or 6) above, so instantaneous high current spikes can be tolerated by these inductors.
- A = Outer Dimension
- B = Height
- C = Vertical Mounting Hole Distance
- D = Lead length
- E = Lead Width
- F = Horizontal Mounting Hole Distance
|There are no products to list in this category.
Coil Winding Specialist, Inc., its affiliates, agents, and employees acting on behalf of Coil Winding Specialist, Inc. (collectively, “CWS”) disclaim any and all liability for any errors, inaccuracies or incompleteness contained herein or in any other disclosure relating to any product.
CWS reserves the right at any time and from time to time to make changes to design, technical specification, or construction of any product listed on this website without notice. CWS also reserves the right to discontinue or limit sale of any product or service available throughout this website on temporary or permanently basis without notice.
CWS highly recommends customers not to use its products offered on this website for inappropriate use and applications. Products should be tested for its suitability by prospective customers in all possible applications and conditions. Customers using or selling CWS products for use in other than recommended applications do so entirely at their own risk and agree to fully indemnify CWS from any damages arising or resulting from such use or sale.
Any Comments, Suggestions or Questions? Contact us! Email: firstname.lastname@example.org
353 West Grove Ave. Orange, California 92865
Call us Toll Free: 1-800-679-3184 or 1 (800) 377-3244
Tel: (714) 279-9010,
Fax: (714) 279-9482
Copyright © 2008, Coil Winding Specialist, Inc
Updated July, 2013
CAGE Code: 5DME2(Registered with www.ccr.gov)